Expert of Systematic Overall Solution for Calcium Material Resource Utilization

+
  • DJ型大倾角挡边带式输送机.jpg

DJ-type high-angle side-wall belt conveyor

Product Introduction: The DJ type large inclination side-wall belt conveyor uses a corrugated side-wall and baffle plate conveyor belt as the traction and carrying components, and is applied to the horizontal or large inclination continuous conveying of various granular, powdery, and small block materials.

Applications: Widely used in hydropower, coal, grain, chemical, and metallurgical sectors.

Whatsapp:

Product Introduction

The DJ type large inclination angle side-guard belt conveyor not only has the characteristics of large conveying inclination angle, compact structure, and small land occupation, but also has the advantages of simple structure, reliable operation, convenient maintenance, and reliable and economical material lifting. For materials with special conveying requirements, such as high-temperature resistant materials or materials containing acids, alkalis, oils, organic solvents, etc., special side-guard conveyor belts with corresponding materials can be used by specifying them when ordering.

Highlight Advantages

  1. It can convey bulk materials at a large inclination angle, saving a large amount of equipment footprint and thoroughly solving the conveying angle that ordinary and textured belt conveyors cannot achieve.
  2. When conveying materials mechanically, the overall investment cost is lower than that of belt conveyors, saving about 20%~30% of the investment cost.
  3. Compared with ordinary belt conveyors, bucket elevators, and scraper conveyors, this model has superior comprehensive technical performance.
  4. When conveying materials vertically, the maximum particle size can reach 250mm

Working principle and structure

The structural characteristic of the DJ type high-inclination belt conveyor is that freely expandable and retractable rubber corrugated vertical "skirts" are glued to both sides of the parallel rubber conveyor belt, and partitions with certain strength and elasticity are glued between the skirts to form a box-shaped bucket. This structure allows the material to be continuously conveyed in the bucket. The transmission principle is to transmit the traction force through the friction between the drive roller and the belt. In order to ensure that the belt has a certain initial tension at the separation point of the drive roller, the belt must be tightened by a tensioning device. The belt runs on the rollers together with the cargo, and the belt is both a traction mechanism and a load-bearing mechanism. Since there is no relative motion between the cargo and the belt, the frictional resistance between the belt and the cargo during operation is eliminated. At the same time, the rollers are equipped with rolling bearings, and the friction between the belt and the rollers is rolling friction, which further reduces the running resistance and thus reduces power consumption and increases the transportation distance.

Production site

Belt conveyor production site
Belt conveyor production site
Belt conveyor production site
Belt conveyor production site
Belt conveyor production site

Technical Parameters

Bandwidth B(mm) 500 650
Flange Height H(mm) 80 120 160 80 120 160
Partition Spacing (mm) 126 252 126 252 378 252 378 126 252 126 252 378 252 378
Inclination Angle β 30° 39 21   52 34 65 45 59 32   78 52 105 73
40° 31 16   40 26 52 34 47 24 — 60 40 85 56
50° 25 13 60 32   42 27 37 19 90 48   68 45
60 20 11 50 26 — 34 23 31 16 75 39   55 36
70 17 — 41 21 — 28 18 25 — 62 32   45 30
90° 10   25     17 — 15   38 —   28 —
Bandwidth B(mm) 800 1000
Flange Height H(mm) 120 160 200 160 200 240
Partition Spacing (mm) 126 252 378 252 378 252 378 504 252 378 252 378 504 252
 

Inclination Angle β
30°   99 65 136 94   148 113 186 126 — 207 159 —
40   76 50 110 72 — 114 87 150 99 — 160 122 ——
50° 113 60   88 58 139 91   120 79 195 128    
60 95 49 — 72 47 113 74   98 64 159 105  — 229
70° 77 40   58 38 92 61   80 52 130 85   187
90° 47     36 — 57 37   49 — 80 52   115
Bandwidth B(mm) 1000 1200 1400
Flange Height H(mm) 240 160 200 240 300 200
Partition Spacing (mm) 378 504 252 378 252 378 504 252 378 504 336 504 252 378
Inclination Angle β 30 283 229 223 154 — 250 191 — 342 275 410 350 — 229
40° 231 176 180 118 — 193 147 — 280 231 352 276 — 231
50° 185 141 144 95 235 154     224 170 290 221 281 185
60° 151   117 77 191 126   278 183   237 180 229 151
70° 123   96 63 156 103   226 149   193 147 187 123
90° 76   59   96 63   139 91   118 90 115 75
Bandwidth B (mm) 1400            
Flange Height H(mm) 200 240 300 400            
Partition Spacing (mm) 504 252 378 504 336 504 420 504            
Inclination Angle β 30° 229   422 342 512 437 780 707            
40° 175   345 262 440 345 709 614            
50°   — 276 210 363 276 634 515            
60°   342 225   296 225 549 420            
70°   279 184   241 183 451 343            
90°   171 113   148 112 277 210            

This configuration table is for reference only and may vary depending on the customer's geographical environment and requirements. For more detailed information, please Contact Us:18031851036。 

Free access to more product information

If you are interested in our products, please leave your email, we will contact you as soon as possible, thank you!

Submit Message

Related Cases